Velleman K8200 Manual do Utilizador

002 - CONNECTING THE PRINTER Now that you have an idea what 3D printing entails, we can continue and connect the printer to your computer. First make

Connect the wires to the blue screw connector. Notice the polarity. The red wire is positive and the black is negative. Now connect the adapter to th

Since this is a DIY kit it is possible that the AC plug does not fit the sockets in your country. If this is the case please buy a correct plug at yo

The controller board of the printer has 4 motor drivers, these are the 4 little PCBs that sit on top of the main board.

These drivers control the current that flows through each motor. To do that correctly each of them needs to be calibrated. Take your multimeter and a

Adjust the little trimmer on the driver with the ceramic screwdriver until you measure 0.425V.

Repeat this process for the other 3 motor drivers. In the following steps we will test all the motors of the printer, it is possible due to stiff me

The text on the button should change from “Connect” to “Disconnect”. In the log view on the bottom of Repetier you should see the printer showing the

UNDER CONSTRUCTION • LINUX UNDER CONSTRUCTION Now we can configure Repetier so it knows what printer it will be talking to. First, if you haven’t alr

Now select the “Manual Control” tab. Now we will test each function of the printer separately.

Press the Z + arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The Z AXIS should go UP 10 mm, ever

Press the Z - arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The Z AXIS should go DOWN 10 mm, ev

Press the X + arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The X AXIS should go LEFT 10 mm, ev

Press the X - arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The X AXIS should go RIGHT 10 mm, e

Press the Y + arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The Y AXIS should go FORWARD 10 mm,

Press the Y - arrow for 10 mm (The arrow has 3 active areas where you can click, choose the one that shows 10mm). The Y AXIS should go BACK 10 mm, ev

If everything went right so far you know that each motor is wired correctly. Now we will test if the extruder works. Press on the “Heat Extruder” butt

There you should see a graph indicating the temperature of the extruder (RED) and the temperature of the heated bed (BLUE). The red line should rise t

• Speed = 100 • Extract = 5 • Retract = 5 Then press the following button: The extruder motor should turn a bit and make the large gear turn to t

You should see the following dialog window: Change the settings on this tab to the ones below (for the “Port” setting you should use the Virtual COM

The extruder motor should turn smoothly. If the LARGE GEAR does not move or moves in the opposite direction you wired something wrong. Find and corre

The extruder motor should turn smoothly. If the LARGE GEAR does not move or moves in the opposite direction you wired something wrong. Find and corre

If everything went right so far you know that the extruder will work, now we will test the HEATED BED PCB. Make sure the temperature for the HEATED B

The BLUE line in the temperature graph should start to rise, and you should see the current temperature of the HEATED BED PCB rise. (Be careful becau

Once it has reached 50 °C the graph should look like this: Now you can turn of the HEATED BED PCB by clicking on the “Heat Printbed” button again.

You should see the temperature graph drop to room temperature over time. Now we will test the fan. Slide the slider for the fan to 100% and click on

The fan should begin to blow air in the direction of the extruder. If the fan does not turn, make sure the slider is at 100% and check your wiring. I

Next move the HEATED BED PCB completely to the LEFT by hand. Put your finger on the micro switch of the X AXIS, do not press it.

Now press the “Home X AXIS" button.

As soon as you have pressed this button the print bed will move towards the micro switch that your finger is resting on. Quickly press the micro swit

For the “Printer” tab you should use the following settings: For the “Printer Shape” tab you should use the following settings:

Put your finger on the micro switch of the Y AXIS, do not press it. Now press the “Home Y AXIS" button.

As soon as you have pressed this button the print bed will move towards the micro switch that your finger is resting on. Quickly press the micro swit

Put your finger on the micro switch of the Z AXIS, do not press it.

Now press the “Home Z AXIS" button. As soon as you have pressed this button the Z CARRIAGE will move towards the micro switch that your finger

Now we have tested all the functions of the printer. We can now start the calibration process. This will be explained in the next chapter.

For the “Advanced” tab you shouldn’t change anything. Press “OK” to save your changes. In the main window under “Temperature” you should select the f

First strip the end of the cable so you have 15 cm (5.9") of free wire. Be careful not to cut too deep while you are stripping the cable.

Loop the wire through the first tie wrap as shown in the picture.

Use the clamp-on filter as shown in the pictures below.

Now loop the wire through the second tie-strip.